How to Choose Chandelier Bulbs Without Creating Glare
A client sent me a photograph last winter of an eight arm crystal fitting she had just had hung, asking why it looked nothing like the showroom. The frame was right, the drops were real lead crystal, and the room was the right size for it.

A client sent me a photograph last winter of an eight arm crystal fitting she had just had hung, asking why it looked nothing like the showroom. The frame was right, the drops were real lead crystal, and the room was the right size for it. The problem was in the sockets: three clear filament candles, two frosted golf balls, two warm white candles from a supermarket multipack and one dead one. Eight arms, four different colours of light, and a glare so sharp you could not look up at it without squinting.
Bulbs are the cheapest part of a chandelier and they decide more of how it looks than anything except the crystal itself. In my family's workshop we used to send fixtures out with a note about lamping, and it was ignored more often than it was read. So here is what that note said, updated for LED, and the order in which to make the decisions.
Start with the cap, because you cannot judge it by eye
The cap is the metal base that screws or pushes into the socket, and getting it wrong is the one mistake that leaves you with a boxful of bulbs you cannot return.
Most European chandeliers take E14, the small Edison screw, sometimes written SES. North American fixtures usually take E12, called candelabra, which looks almost identical and will not fit an E14 socket. Older British fittings may have B15, a small bayonet with two pins. A good number of modern glass arm chandeliers use G9, a flat two pin capsule that pushes straight in, and some slimline arms use G4.
Measure rather than guess. The number is the diameter of the screw thread in millimetres, so an E14 thread is 14 mm across and an E12 is 12 mm. If the old bulb is in your hand, a ruler across the widest part of the thread settles it in five seconds. If the fixture is new, the figure is on the spec sheet under lamp base or cap type, which is one of the few lines on those sheets that is never ambiguous.
One quiet trap: adaptors exist that convert E12 to E14 and E14 to E27. They work electrically and they add 10 to 20 mm of height, which on a chandelier pushes the bulb up out of the candle cup and ruins the proportion. I would rather buy the right cap than fix the look afterwards.
Shape, and what each one does to the crystal
Shape is not only decorative. It changes where the light leaves the bulb, and on a crystal fixture that decides whether the drops throw colour or sit dull.
| Shape | Common code | Suits | What it does to the light |
|---|---|---|---|
| Candle, straight | C35 or B35 | Classic brass and crystal, candle cups | Light leaves the sides and the tip, which is what cut drops need |
| Candle, bent tip | C35T | Period and Maria Theresa styles | Same as straight, with a flame suggestion from below |
| Golf ball | G45 or P45 | Shaded chandeliers, modern frames | Wider, softer spread; less sparkle, less glare |
| Capsule | G9 | Glass arm and sleeve fittings | Point source hidden inside glass, very even |
| Tubular | T25 | Tall narrow sleeves | Light along the length, no hot spot at the tip |
Height matters as much as shape. A candle lamp that sits 100 mm tall in a candle cup designed for an 85 mm lamp will show its cap collar above the rim, and on a fixture with eight arms that collar repeats eight times at eye level. Measure the cup depth and buy a lamp no more than about 15 mm taller than it.
Clear filament bulbs are the wrong default
The advice everywhere is that crystal needs a clear bulb with a visible filament, because a point source is what makes cut glass throw rainbows. The physics is right. The advice is still wrong most of the time, and I say that as someone who grew up believing it.
Here is the part that gets left out. Sparkle depends on your pupils being open enough to see it. An exposed filament at 2700 K sitting 2 metres above a dining table is roughly as bright, to the eye, as a bare candle flame held at arm's length, and your pupils react to the brightest thing in view. They close, the drops go grey, and you get glare instead of sparkle. I have watched this happen in a client's hallway where the fitting hung at 2.1 metres because of a low ceiling, and swapping to frosted candles made the crystal look brighter, not duller.
So the rule I use now is about geometry rather than taste. Clear filament lamps if the bulbs sit above normal sightlines, roughly 2.4 metres or higher, or if the fixture is on a dimmer you will actually keep at a third of full output. Frosted or opal if the fitting hangs lower than that, if anyone sits facing it, or if there is a mirror or a glazed picture opposite that will double the source. Over a stairwell, where you look up at it from below only in passing, clear every time.
There is one exception I will defend. A fixture with deep candle sleeves, the kind that cover two thirds of the lamp, hides the filament anyway, and in those a clear lamp gives you the best of both. Check how much of the sleeve is open before you decide.
Brightness is a per arm decision, not a per room one
People shop for a total lumen figure and divide it by the number of arms. That gives a defensible number and a chandelier that looks wrong, because the eye reads each individual source as either comfortable or harsh regardless of the total.
Useful anchors. An old 25 watt incandescent candle produced roughly 200 lumens; a 40 watt one around 420. For a crystal fixture over a dining table I want 200 to 250 lumens per arm, which is 1,600 to 2,000 lumens across eight arms and plenty for a room of 16 square metres with anything else switched on. For a hallway or a bedroom, 130 to 180 per arm. Above about 300 lumens per lamp a clear candle becomes uncomfortable to sit under at any sensible height.
Colour temperature should be 2700 K for warm brass and leaded crystal. Push to 3000 K only with chrome or nickel frames and modern optical glass, where 2700 K can look slightly yellow against cool metal. Some filament lamps are sold at 2200 K for an amber look, which is attractive in a bar and flattens crystal badly, because there is too little blue in the spectrum for the drops to split.
Colour rendering matters more here than in most rooms, since crystal is a prism and a bulb with a weak spectrum has less to split. Look for CRI 90 or above and, if the figure is published, an R9 value over 50, which is the detail I go into in the piece on what CRI means when buying bulbs.
Dimming is where the purchase goes wrong
Almost every complaint I hear about new chandelier bulbs is really a dimmer complaint, and it surfaces a week after the order.
Check three things before buying. First, that the lamp is stated as dimmable, not merely compatible with your fitting. Second, your dimmer's minimum load. A dimmer specified at 10 to 250 watts will not behave with four 2.5 watt LED candles, because 10 watts of load is the floor and you have given it 10 exactly, which is where flicker at low settings comes from. Eight lamps solve it; four often do not. Third, leading edge versus trailing edge. Older leading edge dimmers buzz with LED and dim in visible steps; a trailing edge module costs about 25 to 40 pounds and fixes it properly.
Enclosed fixtures add one more line. If the lamp sits inside a closed glass shade with no ventilation, buy a lamp rated for enclosed use. Standard LED candles in sealed shades run hot, the driver cooks, and they fail in months rather than years, which is the same failure mode behind the short lives of some integrated LED chandeliers.
Buy the whole set at once, plus two
Colour consistency between production batches of the same model is poor, even from good manufacturers. Two lamps bought eight months apart can differ by 100 K or so, which you will not notice on a single pendant and will notice immediately on a row of eight arms.
So buy the full complement in one order, from one seller, and add two spares to the same order. Write the model code and the cap on a strip of tape inside the ceiling canopy or on the back of the switch plate. When one fails in two years, you fit a matching spare in a minute rather than starting this decision again. More on comparing what you are actually buying sits in the buying lighting section.
FAQ
What bulbs does a chandelier usually take?
Most European chandeliers take E14 small Edison screw candles, North American ones take E12 candelabra, and many modern glass arm fixtures take G9 capsules. Measure the thread diameter in millimetres rather than matching by appearance, since E12 and E14 look nearly the same.
Should chandelier bulbs be clear or frosted?
Clear if the lamps sit above about 2.4 metres or stay dimmed, frosted if the fitting hangs lower or anyone sits facing it. Below normal sightlines a clear filament causes glare and the crystal looks duller, not brighter.
How bright should each bulb in a chandelier be?
Around 200 to 250 lumens per arm over a dining table, and 130 to 180 in a hallway or bedroom. Totals matter less than the individual source, which turns harsh above roughly 300 lumens in a clear candle.
Why do my dimmable LED chandelier bulbs flicker at low settings?
Usually because the total load sits at or below the dimmer's minimum, which is common with four small LED lamps. Either add lamps, fit a trailing edge dimmer module, or choose slightly higher wattage lamps so the load clears the floor comfortably.
More in Buying Lighting
Buying Lighting
What to Do When a New Chandelier Arrives Damaged
A crated chandelier arrives on a tail lift, the driver has eleven more drops to make, and he wants a signature.
Buying Lighting
How to Buy Replacement Glass Shades That Actually Fit
One shade on a five arm chandelier cracks when a door slams, and suddenly a fixture that cost 400 pounds is unusable.
Buying Lighting
What Is CRI in Lighting and Why It Matters When Buying Bulbs
You fit new LED bulbs, flick the switch, and the room looks oddly flat.