Lustr Sazan logo Lustr SazanChandeliers and the light they give
Chandeliers

Why a Chandelier Hangs Crooked and How to Level It

A customer in a first floor flat rang me three days after an install to say her new 12 arm chandelier was leaning. I was sure it was not, because I had levelled it before I packed up.

An installer holding a spirit level across the body of a twelve arm crystal chandelier while checking the ceiling canopy

A customer in a first floor flat rang me three days after an install to say her new 12 arm chandelier was leaning. I was sure it was not, because I had levelled it before I packed up. When I got there she was right: the whole fixture tipped about 8 millimetres towards the window, which on a 700 millimetre spread is enough that your eye catches it from the doorway every single time you walk in.

A chandelier that hangs crooked is almost never crooked for a mysterious reason. In the few hundred ceiling lights I have hung, it has come down to one of five things, and four of them are fixable in under half an hour without taking the fixture down. The fifth is the ceiling, and that one takes a different approach entirely. Here is how I work through it, in the order that finds the fault fastest.

First work out what is actually tilted

Before touching anything, find out whether the body of the chandelier is off level, or the chain is hanging out of plumb, or the arms are at different heights while the body is fine. These three faults look identical from across the room and have nothing in common.

  1. Measure from the floor to two opposite arms. Use a tape and have someone hold the other end. If the two figures differ by more than 2 millimetres, something is off. Note which side is low.
  2. Turn the chandelier 180 degrees on its chain and measure again. If the same arm stays low, the fault is in the chandelier. If the low side swaps to the other wall, the fault is in the ceiling or the canopy.
  3. Hold a spirit level across the top of the body, not across the arms. Arms get knocked and bent over the years. The cast or pressed body is the reference surface.
  4. Look at the chain where it leaves the canopy. A chain that exits at an angle rather than straight down means the support point is not where the hole is.
  5. Check the arms are fully seated. On many chandeliers each arm screws into a threaded socket in the body. One arm half a turn short sits visibly lower than its neighbours.

That sequence takes about ten minutes and tells you which of the next sections applies. Skipping it is how people end up bending arms to correct a crossbar problem.

The five causes, in the order I find them

By frequency, across my own jobs, loose or unevenly seated arms account for roughly a third of complaints. They are also the easiest fix: hold the arm, turn it in until it stops, then tighten the collar or locking screw. If an arm will not go all the way in, there is usually old thread sealant or a burr in the socket.

The second most common is the crossbar, the metal strap screwed across the ceiling box. If one of its two screws is tighter than the other, the strap sits at a slight angle and the threaded nipple in its centre points off vertical. Everything hanging below then leans. Slacken both screws, press the strap flat to the box face, and tighten them in alternating quarter turns the way you would do wheel nuts.

Third is the canopy sitting on an uneven ceiling. Plaster around a ceiling box is often built up on one side, and a rigid canopy pressed against that high spot pushes the whole assembly over. Back the canopy nut off a few millimetres so the canopy just kisses the ceiling rather than being clamped to it. You lose nothing structurally, because the weight is carried by the nipple and strap, not the canopy.

Fourth is a twisted chain. Chain links alternate at 90 degrees, so if the chain has been hung with a twist in it, the fixture rotates and can also hang slightly off plumb where the twist is taken up at the loop. Unclip the chain at the canopy loop and let the chandelier hang free for a minute. It will untwist itself. Then reconnect without forcing the link.

Fifth is the ceiling, and I will come back to that.

When the chain is the adjustment point, remember that you cannot change length in smooth increments. Each link you remove or add changes the drop by one link, and because the links alternate direction, taking out a single link also rotates the fixture a quarter turn relative to the ceiling.

On a 50 millimetre link chain that means your drop only comes in 50 millimetre steps unless you add a short section of smaller chain or an adjustable nipple at the top. For a dining room where you want the body at exactly 760 millimetres above the table, that matters. I keep a handful of 20 millimetre links in the van for this reason, and I will use two short links rather than argue with the customer about 50 millimetres. The full method for taking a chain apart without scratching the finish is in how to shorten a chandelier chain.

Bending the arms is not the fix

Search for this problem and you will find plenty of advice to simply bend the low arm upward until the chandelier looks level. I understand why it is popular. It works in thirty seconds and the room looks right. I still refuse to do it, for three reasons.

The first is that the lean is almost always in the body or the support, so bending an arm corrects the appearance of one arm while leaving the other eleven wrong. People then bend the next one, and the next, and the fixture ends up with a soft wavy profile that reads as damage rather than design.

The second is metal fatigue. Brass and steel chandelier arms are usually tube with a wall around 0.8 to 1.2 millimetres. Bending work hardens the bend and thins it. I have taken down a 1960s eight arm fixture where two arms had cracked at precisely the point someone had straightened them, and a cracked arm with a live conductor running through it is not a cosmetic problem.

The third is money. On antique and good quality modern pieces, original unbent arms are a large part of the value. A set of replacement arms rarely matches in colour, and matching across decades of lacquer ageing is close to impossible. The same logic applies to crystals, which I covered in how to replace chandelier crystals so they match.

Flush and semi flush fixtures tilt differently

A fixture with no chain has no self levelling at all, so every bit of error in the box and the crossbar shows up in the glass. There is also nothing to rotate, so the test of turning it 180 degrees means removing it.

The fix is usually shims. A pair of plastic washers, or a strip of thin packer behind the low side of the crossbar, will bring the mounting face back to level. Fibre washers in 0.5 and 1 millimetre thicknesses cost pennies and solve most of these. Do not shim with cardboard, and do not shim between the canopy and a painted ceiling where it will show.

The other cause specific to these fixtures is the glass sitting unevenly in its holder. Loosen all three thumbscrews, let the shade settle under its own weight, then nip them up in sequence rather than tightening one fully first.

When the ceiling itself is out of level

In older buildings the ceiling often slopes a little, and in rooms that have been converted it can slope a lot. A chandelier on a chain hangs plumb regardless, which means a level chandelier in a sloping room will look crooked relative to the ceiling line even though it is perfectly vertical.

This is the one case where I ask the customer what they want to look right. If the ceiling drops 15 millimetres across the room, you can either hang plumb and accept the visual gap at the canopy, or tilt very slightly to split the difference. I usually hang plumb and distract the eye with a ceiling medallion, which hides the mismatch at the canopy where it is most obvious. For a genuinely pitched ceiling the mounting hardware itself has to change, and that is covered in hanging a chandelier on a sloped ceiling.

If you are chasing a lean of more than about 20 millimetres, check the box fixing instead. A box that has pulled part way out of a joist will tilt, and that is a support question rather than a levelling one.

FAQ

Why does my chandelier hang crooked after installation?

Most often one arm is not screwed fully into the body, or the crossbar in the ceiling box is pulled to an angle because one of its screws is tighter than the other. Turn the fixture 180 degrees on its chain and measure again. If the low side moves with the fixture, the fault is in the chandelier.

Can I bend a chandelier arm to level it?

I would not. Bending thins and hardens the tube at the bend, and on older fixtures that is where arms crack. It also only hides the symptom when the real cause is in the body or the support. Fix the seating and the crossbar first.

How level does a chandelier need to be?

Within about 2 millimetres measured between opposite arms is where most people stop noticing. Anything beyond 5 millimetres on a wide fixture reads as crooked from the doorway, which is where everybody looks at it from.

Does a twisted chain make a chandelier hang wrong?

It rotates the fixture and can pull it slightly out of plumb at the top loop. Unclip the chain at the canopy, let the chandelier hang free so the twist releases, and reconnect it without forcing the link into position.

NF
Nikolai Ferreira

Nikolai is an electrician who has hung several hundred ceiling lights, some of them very heavy. He writes about installation, support and safety without skipping the dull parts.

More posts by Nikolai

More in Chandeliers

01doorganico 084goad 3hot8 4465456 after5internprogram ahandfulofblessings ahmadpc ahomcybersecurity allodialresources annodex antiquesandperiodcollectibles aotc asianworldkashmir beedlectrics bloggertemplatefree bluefeatheragency bodyweightsolution campaign08blog carfixadvisor catstreetcollective cbstvsports cnfanspurchasing committeeof500yearsofdignityandresistance covertopsdjs cs-kaiyuangame cuestacomunicaciontotal cxoutlet dancebetgame deskgearhub destinyvillastay detectmagazine di33 diamondsteelbuildings donmo dyanadropship emarsysfinance emimattl escapechan eskitarih evautoplay everythingweddings-orlando farmzone feedviewerapp foxstudiosscratch gamevui123 gleasongrade greetingsday hacklabasu haskell iw-kaiyun jagoanproperti jilidskripsi joltbusinessfinance juegodepokergratis juegospucca kaeru-festival latestmehndidesigns lestanzediottaviano litemagazines localcommunityhero mariashebets menswheels newwebstechs1 nikkit ootheday oxigenvpn plurfitness prefetial probudgetcarpetcleaning psychicmrsmartin pyaten qvantor rejoignezlogis rexzbot riselayouts ruchin rwxqsgd5 sakaltime shibiaowang shop-bot skrtips spotlesshaven strcoding tetapatrium topselller uneplanteartificielle vipertechcr webtech1223411 wo-kygaming yamaha-mekar yeknava yoybuysheets zenunwa yamaha-mekar jilidskripsi ankertoto ankertoto ankertoto ankertoto